News | May 31, 2022

FRCSW Goes to the Movies: “Top Gun: Maverick”

By Jim Markle

It takes a lot to make a movie.

In the case of Tom Cruise’s latest film, “Top Gun: Maverick,” it took the artisans, engineers and staff of Fleet Readiness Center Southwest (FRCSW) to not only provide an authentic presentation of the aircraft used in the film, but also support for the filming itself.

FRCSW painted one of the film’s two F/A-18 Super Hornet fighter aircraft and led the installation design of the audio/visual (A/V) equipment fixed in the cockpit of an F-model Super Hornet used in the movie’s production.

“When it came time to start installing the A/V cockpit equipment and the production team was in place at our first location at Naval Air Station (NAS) Lemoore, we had meetings with the director and some of the producers, including Tom Cruise. He was very passionate about making this the greatest aviation film of all-time,” said F/A-18 MRO Engineering Department Head Jonathan Ramba who oversaw the installation.

“The production crew used new Sony Venice 6K cameras that weighed about eight pounds with a lens. The cinematographer wanted four of these to be installed on the aft seat’s glare shield, but settled for three full camera bodies mounted and a sensor block, which acted as a fourth camera. All said, the total weight of the equipment on the aft glare shield was about 40 pounds.”

Ramba’s involvement with the filming began in July 2018 with a call from the F/A-18 & EA-18G Program Office (PMA-265) asking FRCSW’s F/A-18 Fleet Support Team to accommodate a visit from the Top Gun production crew. 
 
“I was the E/F/G FST Structures Engineering Lead at the time, so I was tasked to lead this project,” Ramba noted.

About two weeks later, he traveled to NAS Lemoore to discuss the installation and locations of the cameras on the interior and exterior of the aircraft.

He developed a proposal afterward and worked with Naval Air Systems Command (NAVAIR) to establish the required action for approval. 

Filming was slated to start by the end of September 2018, and a fit check had to be completed approximately two weeks prior to that.  

Knowing the effort demanded a top-notch team to meet the timelines, Ramba enlisted aerospace engineer Tony Pacheco for his expertise in design and MRO-E F/A-18A-F and EA-18G Structural Analysis Division Head Manny Hernandez to handle stress analysis considerations.

To assess the feasibility of the production crew’s camera mounting requirements, Pacheco traveled to FRC West to adapt the Super Hornet provided by Strike Fighter Squadron 122 (VFA-122).

“After all mounts were designed and approved for use by the PMA-265 Airworthiness Certification Engineer (ACE), I coordinated with third-party machine shops designated by Paramount Studios to have all parts machined to specifications and delivered to the production crew,” he said.

“Ultimately, all designed mounts fit perfectly, and all filming equipment was successfully installed. After a shake-out flight, Tom Cruise went on a quick test flight and it was determined that the entire assembly worked perfectly.”

Next, to gain an Interim Flight Clearance (IFC), Pacheco developed drawings to reflect the aircraft configuration change that included the installation processes of the mounts and cameras, and the temporary removal of any components.   

“After all flight limits were established within the IFC by PMA-265, I quickly familiarized myself with them and ensured the production personnel and flight crew were aware of the limits to avoid any issues,” he said.

Approximately one month before filming, Hernandez completed a crucial strength analysis for the design of the cockpit camera mounts in less than three weeks.
He also analyzed the glare shield, a 0.063-inch thick aluminum component that held the 40-pound camera rig, and subjected it up to a 7.5 g acceleration rate along multiple directions.

“I used MSC Patran and Nastran (software) to simulate the added equipment with the existing affected structure being subjected to the considered loads,” he said.

Meanwhile, in the FRCSW paint shop, six artisans began duplicating the F-model paint job on a single-seat E model Super Hornet from the command’s long-term storage area.

“We replicated the paint job on that aircraft for non-flying scenes and close ups of the actors near the aircraft on the ground,” said Tommy Sapien, Aircraft Services Paint Production Line Manager.

After applying several polyurethane top coats and stencils, the project was complete in five days.

“Getting the details correct were a challenge because we did not work off of any blueprints,” Sapien said. “We did the paint job based on pictures we had of the two-seater Super Hornet from the flying scenes in the movie.”

In February 2020, the E-model Super Hornet was delivered to FRC Southeast where it underwent modification. It is currently a Blue Angel.

“Top Gun: Maverick” took approximately eight months to film at a variety of locations including NAS Lemoore, Whidbey Island, Fallon and Naval Weapons Station China Lake. In-flight filming concluded in the winter of 2019.

Collectively, FRCSW and FRCW teammates devoted more than 1,000 hours to the production of the film while simultaneously completing their real jobs: Providing mission-ready Super Hornets to the fleet.

“Top Gun: Maverick” was released in theaters May 24, and no, Tom Cruise did not actually fly an F/A-18 Super Hornet. A real “Top Gun” piloted the aircraft. We hope the audience enjoys the ride!

Editor’s note: FRCSW would like to acknowledge the following teammates for their support in the production of “Top Gun: Maverick”: FST Project Engineer Nicholas Candrella, FST Senior Aerospace Engineer Daniel Collins, FRCW Engineering Site Lead Mariana Magana, FRCW Aerospace Engineer Calvin Gong and MRO-E Senior Aerospace Engineer Jake Schomaker. 
 
 
 
 
 

May 31, 2022

FRCSW Goes to the Movies: “Top Gun: Maverick”

FRCSW painted one of the film’s two F/A-18 Super Hornet fighter aircraft and led the installation design of the audio/visual (A/V) equipment fixed in the cockpit of an F-model Super Hornet used in the movie’s production.

May 16, 2022

FRCSW Provides Engine Power to Naval Ships

Production of the LM2500 began in 1969 by the General Electric Co. The engines were first used by the Navy to power Spruance and Kidd-class destroyers in the 1970s. A decade later, installation of the reliable engines expanded to include Oliver Hazard Perry-class frigates, Ticonderoga-class cruisers and Arleigh Burke-class destroyers.

April 11, 2022

FRCSW Names FY 2021 Civilian of the Quarter

Fleet Readiness Center Southwest (FRCSW) selected James Trowsdell as its Fiscal Year (FY) 2021 Civilian of the Quarter, fourth quarter.

March 28, 2022

FRCSW Celebrates Women’s History Month

In recognition, Fleet Readiness Center Southwest (FRCSW) is highlighting the life and work of aerospace engineer Janene Valenzuela.

March 15, 2022

Finch Family Supports FRCSW, Navy

The Finch’s tradition is one of service. Service to the nation, to the Navy and Fleet Readiness Center Southwest (FRCSW). Service that totals 70 years to date and counting

March 8, 2022

FRCSW Inducts Its First MV-22 to Suffer Mishap

The right-hand inner composite skin of the $75 million aircraft sustained a four-foot by two-foot crack with other, but minor, composite damage.

Feb. 22, 2022

FRCSW VRT Supports USCG Ship Repairs

But the VRT’s expertise is not strictly limited to requests by the Navy. The nation’s Coast Guard is also a customer.

Feb. 14, 2022

FRCSW Teammates Help Rescue Lost Hiker

Last month a group of FRCSW teammates that included Adam Kimmerly, Thom Jarvis, Camille Delaflor, Paul Douvier and Marc Rasp (all from the command’s Fleet Support Team) found themselves playing a pivotal role in the rescue of a lost hiker in the Anza-Borrego Desert State Park, the largest state park in California.

Jan. 24, 2022

FRCSW Selects its 2021 Mentor of the Year

At Fleet Readiness Center Southwest (FRCSW), Senior Chief Yeoman (YNCS) Jolyn Jones is the command’s 2021 Mentor of the Year (MOY).

Jan. 11, 2022

FRCSW Lands CNO Aviation Safety Award

In recognition of its consistent and effective airborne operations, Fleet Readiness Center Southwest (FRCSW) was recently selected to receive a Chief of Naval Operations (CNO) Fiscal Year 2020 Aviation Safety Award.